Locomotive hydraulic reset machine product details

Locomotive hydraulic machine reset (common name on machine) is an ideal tool for mining road maintenance. Suitable for mining operations, operating under 15 tons for reduction of locomotive and car.

The whole machine part and main structure features of hydraulic reset machine

1, the whole machine part: the whole machine is mainly composed of hydraulic transmission part, lever mechanism part and transverse pulley frame part.

2, the main mechanism: This machine adopts two coordinate hydraulic moving. The utility model has the advantages of compact structure, high work efficiency, stable reliability and low labor intensity. Especially because no power consumption, so good security. It is suitable for 15 tons of locomotive or harvester on the road (reset) operation.

3, lifting system (including lever part and hydraulic transport part). A, lever mechanism: mechanism by the main lever, vice lever, connecting rod, roller, side hook and other parts. Simple structure, easy maintenance and operation. B, lifting hydraulic transmission parts: hydraulic transmission part is mainly composed of a manual lever or column pump, oil cylinder, oil tank etc.. The utility model has the advantages of high oil pressure, little leakage, no noise, long service life and high degree of freedom in adjusting height range. C, a side hook is arranged on the lifting, which ensures the stability of the reset center of gravity and is convenient and reliable. D, transverse roller frame part: transverse roller frame part in addition to the lateral lever mechanism and transverse hydraulic transmission part, the main set of lateral pulley. To have been slipping out of the vehicle or the tramcar wheel, the wheel rotates, the movement of the sliding platform right into orbit. Quick and convenient. It is mainly composed of a guide frame and the sliding frame etc..

Technical parameters of locomotive hydraulic reset machine

1, maximum load: top column load 15000kg side hook (or joint interface) load 10000kg;

2, the maximum stroke (do not use the actual mark line): top column stroke 150mm side hook (or joint interface) travel 220mm lateral travel 300mm;

3, the weight of the whole machine: 50kg.

Locomotive hydraulic reset machine instructions

1, when unpacking note: do not use wooden inverted before unpacking. Don't use a hammer on packaging for unpacking, to prevent damage to parts. Should carefully pry open a crowbar box, and then put the lid open. The machine took out after the first one by one according to the packing list checked, the clean machine of antirust oil and dirt, and good oil.

2, use: relax the hydraulic lifting part ventilation valve, open the valve on the top or side column hook in the moderate pressure is reduced to the lowest position, the lifting system of machine and the horizontal moving part sleeve (the roller slot above the lifting column below the insert in the transverse sliding inside will); a transverse sliding seat is arranged in the flat solid and level ground (the appropriate position to implement the reset operation); below will reset the machine side hook in the implementation of the appropriate location of the locomotive or car reset.

3, operation: lifting off the oil valve, the control rod is inserted into the Konne press hand, slowly lifting lever, the reciprocating plunger pump core, until the wheels up to the required height, the horizontal baffle set to move the reversing the stall, and the control rod is inserted into the crank hole, operating rod with the hand, with a transverse sliding lifting system will be a lateral move, until the vehicle or the tramcar moved to the desired position, slowly open the oil valve, let the vehicle or the tramcar wheel to slow down, until the completion of the reset (orbit) operation.

4, unloading machine: fully open the responsible for lifting movement back to the oil valve, the top column or side hook down pressure, until the lowest position. Close the oil valve, screw vent valve, remove the reset mechanism.

5, machine maintenance and cycle check: in order to ensure that the machine in each use flexible and reliable, must be effective maintenance of the machine, and periodic inspection. A, must ensure that the machine sliding parts and exposed moving parts do not rust, after use must be on the oil. If the use of longer intervals must be antirust oil. Do not put the machine to fall, knock, bumps, in order to ensure the accuracy of activities. B, once a quarter of the moving parts and oil cycle check. In C, to replace or supplement the hydraulic oil, should be used for the 18-38 viscosity centistoke (temperature of 50 DEG C) specifications, the precision of oil filter is not greater than 20 micron hydraulic oil. In the filling of hydraulic oil shall not be mixed with sand and other debris, and pay attention to every time when filling must be vented to the pump body and the cylinder. D, when the need for maintenance, application of gasoline or diesel (Caution!) clean the oil and the main components, and will not work parts surface caused by scratching and collision, deformation and other damage can affect the normal operation of the machine.

The product has been exported to the United States, France, Canada, Indonesia, Russia, Vietnam, Australia, South Korea, Iran and other countries, access to customer acclaim.